Matek Systems H743-WING STM32H743VIT6 Flight Controller OSD 3~8S MPU6000 MicroSD Blackbox 5V/9V BEC for RC Airplane Fixed-Wing RC Drone FPV Racing

Matek Systems H743-WING STM32H743VIT6 Flight Controller OSD 3~8S MPU6000 MicroSD Blackbox 5V/9V BEC for RC Airplane Fixed-Wing RC Drone FPV Racing

 

FC Specifications

MCU: STM32H743VIT6, 480MHz , 1MB RAM, 2MB Flash

IMU: MPU6000 (SPI1) & ICM20602 (SPI4)

Baro: Infineon DPS310 (I2C2)

OSD: AT7456E (SPI2)

Blackbox: MicroSD card slot (SDIO)

7x Uarts (1,2,3,4,6,7,8) with built-in inversion.

13x PWM outputs(including “LED” pad)

2x I2C

1x CAN

6x ADC (VBAT, Current, RSSI, Analog AirSpeed, VB2, CU2)

3x LEDs for FC STATUS (Blue, Red) and 3.3V indicator(Red)

1x SPI3 breakout

USB/Beep Extender with Type-C(USB2.0)

Dual Camera Inputs switch

5V/9V(12V) for Camera/VTX power switch

High-precision Current Sense

ADC VB2 voltage divider: 1K:10K

ADC AirSpeed voltage divider: 10K:10K

INAV TR/SA VTX control: Yes

Beeper : Yes

RSSI: Yes

Analog Airspeed sensor: Yes

Digital Airspeed sensor: Yes

Static power 160mA@5V

 

FC Firmware

ArduPilot(ChiBiOS): MATEKH743

INAV: MATEKH743 (To be supported soon)

BetaFlight: MATEKH743

 

PDB

Input voltage range: 9~36V (3~8S LiPo) w/TVS protection

2x ESC power pads

Battery Voltage Sensor: 1:10 (Scale 1100 in INAV,  BATT_VOLT_MULT 11.0 in ArduPilot)

Current Senor: 132A,  3.3V ADC  (Scale 250 in INAV,  40 A/V in ArduPilot)

Sense resistor: 60A continuous, 132A burst.

 

BEC 5V output

Designed for Flight controller, Receiver, OSD, Camera, Buzzer, 2812 LED_Strip, Buzzer, GPS module, AirSpeed

Continuous current: 2 Amps, Max.3A

 

BEC 9V /12V output

Designed for Video Transmitter, Camera, Gimbal ect.

Continuous current: 2 Amps, Max.3A

12V option with Jumper pad

 

BEC Vx output

Designed for Servos

Voltage adjustable, 5V Default, 6V or 7.2V via jumper

Continuous current: 8 Amps, Max.10A

 

BEC 3.3V output

Linear Regulator

Continuous current: 200mA

 

Physical

Mounting: 30.5 x 30.5mm, Φ4mm with Grommets Φ3mm

Dimensions: 54 x 36 x 13 mm

Weight: 30g with USB extender

 

ArduPilot Mapping

 

PWM PWM1~PWM13 are Dshot and PWM capable. However, mixing Dshot and normal PWM operation for outputs is restricted into groups, ie. enabling Dshot for an output in a group requires that ALL outputs in that group be configured and used as Dshot, rather than PWM outputs. If servo and motor are mixed in same group, make sure this group run lowest PWM frequency according to the servo specification. ie. Servo supports Max. 50Hz, ESC must run at 50Hz in this group.	S1	PB0	5 V tolerant I/O	PWM1 GPIO50	TIM8_CH2N	Group1
	S2	PB1	3.3 V tolerant I/O	PWM2 GPIO51	TIM8_CH3N
	S3	PA0	5 V tolerant I/O	PWM3 GPIO52	TIM5_CH1	Group2
	S4	PA1	5 V tolerant I/O	PWM4 GPIO53	TIM5_CH2
	S5	PA2	5 V tolerant I/O	PWM5 GPIO54	TIM5_CH3
	S6	PA3	5 V tolerant I/O	PWM6 GPIO55	TIM5_CH4
	S7	PD12	5 V tolerant I/O	PWM7 GPIO56	TIM4_CH1	Gourp3
	S8	PD13	5 V tolerant I/O	PWM8 GPIO57	TIM4_CH2
	S9	PD14	5 V tolerant I/O	PWM9 GPIO58	TIM4_CH3
	S10	PD15	5 V tolerant I/O	PWM10 GPIO59	TIM4_CH4
	S11	PE5	5 V tolerant I/O	PWM11 GPIO60	TIM15_CH1	Group4
	S12	PE6	5 V tolerant I/O	PWM12 GPIO61	TIM15_CH2
	LED	PA8	5 V tolerant I/O	PWM13 GPIO62	TIM1_CH1	Group5
				SERVO13_FUNCTION 120,   NTF_LED_TYPES  neopixel
ADC	No pad 1K:10K divider builtin	PC0	0~36V	on board battery voltage	BATT_VOLT_PIN BATT_VOLT_MULT	10 11.0
	No pad	PC1	0~3.3V	on board current sensor	BATT_CURR_PIN BATT_AMP_PERVLT	11 40
	VB2 Pad 1K:10K divider builtin	PA4	0~36V	VB2 ADC	BATT2_VOLT_PIN BATT2_VOLT_MULT	18 11.0
	CU2 Pad	PA7	0~3.3V	CU2 ADC	BATT2_CURR_PIN BATT2_AMP_PERVLT	7 /
	RSSI Pad	PC5	0~3.3V	RSSI ADC Analog RSSI	RSSI_ANA_PIN RSSI_TYPE	8 1
	AirS Pad 10K:10K divider builtin	PC4	0~6.6V	AirS ADC Analog Airspeed	ARSPD_PIN ARSPD_TYPE	4 2
I2C	I2C1 CL1/DA1	PB6/PB7	5 V tolerant I/O	Digital Airspeed I2C	ARSPD_BUS ARSPD_PIN	1 65
				MS4525 MS5525 DLVR-L10D	ARSPD_TYPE	1 3 9
				Compass	COMPASS_AUTODEC	1
	I2C2 CL2/DA2	PB10/PB11	5 V tolerant I/O	on board Baro DPS310
CAN	CAN1	PD0/PD1	5 V tolerant I/O	F103/F303 CAN Node	CAN_D1_PROTOCOL CAN_P1_DRIVER	1 1
				CAN GPS	GPS_TYPE	9
				CAN Compass	COMPASS_TYPEMASK	0
				CAN Airspeed sensor	ARSPD_TYPE	8
UART	USB	PA11/PA12	5 V tolerant I/O	USB	console	SERIAL0
	RX7 TX7 RTS7 CTS7	PE7/8/9/10	3.3 V tolerant I/O	UART7	telem1	SERIAL1
	TX1 RX1	PA9/PA10	5 V tolerant I/O	USART1	telem2	SERIAL2
	TX2 RX2	PD5/PD6	5 V tolerant I/O	USART2	GPS1	SERIAL3
	TX3 RX3	PD8/PD9	5 V tolerant I/O	USART3	GPS2	SERIAL4
	TX8 RX8	PE1/PE0	5 V tolerant I/O	UART8	USER	SERIAL5
	TX4 RX4	PB9/PB8	5 V tolerant I/O	UART4	USER	SERIAL6
	TX6 RX6	PC6/PC7	5 V tolerant I/O	USART6	RC input/Receiver
				RX6	SBUS/IBUS/DSM
				RX6	PPM

ArduPilot Relay

* Camera-1 and Vsw On by default

* Make sure 2 cameras are set with identical video format, both PAL or both NTSC.

 

# GPIOs

PD10 PINIO1 OUTPUT GPIO(81)   //Vsw pad power switch

PD11 PINIO2 OUTPUT GPIO(82)   //Camera switch

 

# RCx_OPTION: RC input option

28   Relay On/Off

34   Relay2 On/Off

35   Relay3 On/Off

36   Relay4 On/Off

 

e.g.

RELAY_PIN       81    //Vsw GPIO

RC7_OPTION   28    //Relay On/Off, Use CH7 of Transmitter to switch Vsw

RELAY_PIN2     82    //Camera switch GPIO

RC8_OPTION   34    //Relay2 On/Off, Use CH8 of Transmitter to switch camera

 

or

* RELAY_PIN3       81    //Vsw GPIO

* RC9_OPTION     35    //Relay3 On/Off, Use CH9 of Transmitter to switch Vsw

* RELAY_PIN4       82    //Camera switch GPIO

* RC10_OPTION   36    //Relay4 On/Off, Use CH10 of Transmitter to switch camera

 

The configured feature will be triggered when the auxiliary switch’s pwm value becomes higher than 1800. It will be deactivated when the value falls below 1200.

 

Check the pwm value sent from the transmitter when the switch is high and low using the Mission Planner’s Initial Setup >> Mandatory

 

Hardware >> Radio Calibration screen. If it does not climb higher than 1800 or lower than 1200, it is best to adjust the servo end points in the transmitter.

 

H734-Wing vs Wing Series

 

WING series	H743-WING	F765-WING	F722-WING	F405-WING
Launch	Aug.2020	Aug.2019	Dec.2018	Apr.2018
INAV Target	To be updated	MatekF765	MatekF722SE	MatekF405SE
Ardupilot Target	MatekH743	MatekF765-WING	/	MatekF405-WING
Firmware	INAV	INAV,BF	INAV	INAV
	ArduPilot	ArduPilot	BetaFlight	ArduPilot
MCU	480MHz	216MHz	216MHz	168MHz
	STM32H743	STM32F765	STM32F722	STM32F405
	2MB Flash	2MB Flash	512KB Flash	1MB Flash
IMU	MP6000 & ICM20602	MP6000 & ICM20602	MP6000	MP6000
BARO	DPS310	BMP280	BMP280	BMP280
OSD	AT7456E	AT7456E	AT7456E	AT7456E
BlackBox	MicroSD(SDIO)	MicroSD(SDIO)	MicroSD	MicroSD
Dual Camera In	Yes	Yes	Yes	/
5V/9V Switcher	Yes	Yes	Yes	/
Current	High precision	High precision	High precision	104A
Sense	132A	132A	132A
Max.Voltage	36V(8S)	36V(8S)	36V(8S)	30V(6S)
PWM outputs	13	13	8	9
UART	7	7	5	6
CAN	1	/	/	/
Uart Inversion	All	All	All	RX2
5V	2A	2A	2A	2A
9V	2A	2A	2A	2A
Vx	8A/10A	8A/10A	5A	5A
3.3V	200mA	200mA	200mA	500mA
Size	54×36	54×36	54×36	56×36
Weight	30g	26g	25g	25g

Tips

 

ArduPilot Firmware ” MATEKH743″

* Only beta/latest ArduPilot firmwares after Jun.25 support the onboard barometer currently.

* https://firmware.ardupilot.org/Plane/latest/MatekH743/

* https://firmware.ardupilot.org/Copter/latest/MatekH743/

* H743-WING has betaflight firmware preloaded for QC

* If you flash ArduPilot firmware via BetaFlight configurator.  there is a known issue that flash process will freeze at 50% if “full chip erase” is selected.   Disable full chip erase when flashing,  then reset to default in Mission Planner after flashing.

* It is highly recommended to use STM32CubeProgrammer to erase MCU and upload firmware http://www.mateksys.com/?p=6905

 

H743-WING Quick Start Guide, click here

 

Package Included:

1x H743-WING

1x USB/Beep Extender

1x 20cm SH-4P to GH-4P cable for CAN port

1x 20cm SH-6P to SH-6P cable for USB extender.

Dupont 2.54 pins  (Board is shipped unsoldered)